Showing results: 676 - 690 of 696 items found.
-
Frida TD -
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR frida TD. The portable and high performance high-voltage testing and diagnostics device is available in two different configurations: frida: Used for cable and cable sheath testing of medium-voltage cables and electrical equipment up to 20 kV. Another function is insulation testing on electrical equipment.frida TD: Expands the functional scope of frida with the tan delta diagnostics and Monitored Withstand Test (MWT) that combines the cable testing and dissipation factor measurement. This allows for an accurate and comprehensive assessment of the cable condition.* Cable testing and dissipation factor diagnostics in one device* Easy and quick test setup* Automatic testing and diagnostic sequences* Compact dimensions and lightweight
-
National Technical Systems
In vibration testing of high value aerospace hardware, over testing of light, high performance structures is a great concern. Discrepancies between the mechanical impedances and the force capabilities of the mounting structure and the vibration shaker can cause catastrophic structural and functional problems to test item. The effectiveness of the radar depends on it retaining its structural integrity over the entire surface of the antenna and that all its electronics are a) tested at, or near levels they will experience in its service life and b) the resonance of various parts of the radar follow those of the model. Consequently, the vibration test lab required 60 data channels to accurately verify the design of the instrument and its ability to withstand launch, cruise and deployment loads. To avoid over testing, NTS used Force Limiting Test Process using four force transducers to prevent exceeding total load of 1000 pounds.
-
NX5300 -
Marvin Test Solutions, Inc.
The NX5300 is a single slot 3U PXI device and interfaces to the unit under test via an On-Chip Debug (OCD) or JTAG port. The NX5300 is a high performance JTAG based background debug mode (BDM) diagnostic system designed for functional test, development, programming and troubleshooting of microprocessor and microcontroller based embedded processor systems. Advanced capabilities include simultaneous support of up to 255 devices on a single scan chain, support of sixteen NX5300 systems controlled by single host machine and configurable JTAG/BDM clock rates up to 24 MHz. The NX5300 includes 16 high-speed measurement channels. Each channel can measure logic levels, frequency, count events and perform a CRC check at rates up to 100 MHz.
-
ERAVANT
Automotive radar sensors play a vital role in the current development of autonomous driving. Their ability to detect objects even under adverse conditions makes them indispensable for environment-sensing tasks in autonomous vehicles. As their functional operation must be validated in-place, a fully integrated test system is required. Radar Target Simulators (RTS) are capable of executing end-of-line, over-the-air validation tests by looping back a received and afterward modified radar signal and have been incorporated into existing Vehicle-in-the-Loop (ViL) test beds before. However, the currently available ViL test beds and the RTS systems that they consist of lack the ability to generate authentic radar echoes with respect to their complexity. The paper at hand reviews the current development stage of the research as well as commercial ViL and RTS systems. Furthermore, the concept and implementation of a new test setup for the rapid prototyping and validation of ADAS functions is presented. This represents the first-ever integrated radar validation test system to comprise multiple angle-resolved radar target channels, each capable of generating multiple radar echoes. A measurement campaign that supports this claim has been conducted.
-
Model BHP/EPB™ -
MB Dynamics Inc.
The new Model BHP/EPB™ Brake Hydraulic Pressure (BHP) and Electric Parking Brake (EPB) Systems test bench from MB Dynamics accurately measures and controls the hydraulic pressure and EPB power levels applied to brake calipers during automotive buzz, squeak and rattle (BSR) testing, as well as brake durability, stability, functional or performance testing. Varied brake pressures are applied according to timing diagrams, as well as automated or manually program-controlled repeat cycles, as required to assess brake caliper/rotor assembly noise, useful service life, and other critical performance metrics.
-
WECO 8020, 8030 -
Radian Research, Inc.
WECO Meter Qualification Boards by Radian Research enable extensive functional testing of single-phase and three-phase revenue grade electricity meters. Unlike Warm-up Boards and Load Boards that are limited to just powering the meter or applying a fixed current, WECO Meter Qualification Boards can test a variety of communications, disconnect and safety features. The WECO 8020 and 8030 have varying capabilities based on your requirements. They feature an innovative open socket design exclusive to RADIAN that ensures optimum operator safety. Capability, versatility and safety combine to make WECO Meter Qualification Boards THE logical choice.
-
MD-100-CM-2WD -
Mustang Dynamometer
High throughput demands of Centralized Emission Inspection require the use of rugged and durable emission inspection equipment. Designed from inception to withstand punishing use and misuse, Mustang Dynamometer has set the performance standards of equipment manufactured and used worldwide for centralized emissions testing. Our pioneering experience has led us to be the world leader in the design and manufacturing of rugged inspection and maintenance hardware and software for the I/M industry. We have centralized testing lanes installed all over the world in climates from cold to hot and from wet to dry. By the end of 2020 we estimate that our equipment will have performed nearly 1 billion vehicle tests. Continuous improvement leads us to innovative solutions based on our knowledge of design, service, maintenance, ergonomics and overall functional capabilities. Mustang I/M Centralized Emission Inspection equipment is designed for our customer’s demands.
-
MD-100-M-2WD -
Mustang Dynamometer
High throughput demands of Centralized Emission Inspection require the use of rugged and durable emission inspection equipment. Designed from inception to withstand punishing use and misuse, Mustang Dynamometer has set the performance standards of equipment manufactured and used worldwide for centralized emissions testing. Our pioneering experience has led us to be the world leader in the design and manufacturing of rugged inspection and maintenance hardware and software for the I/M industry. We have centralized testing lanes installed all over the world in climates from cold to hot and from wet to dry. By the end of 2020 we estimate that our equipment will have performed nearly 1.5 billion vehicle tests. Continuous improvement leads us to innovative solutions based on our knowledge of design, service, maintenance, ergonomics and overall functional capabilities. Mustang I/M Centralized Emission Inspection equipment is designed for our customer’s demands.
-
KD-9363-EM -
King Design Industrial Co., Ltd.
The purpose of vibration testing is to make a series of controllable vibration simulation in lab, no matter generated by natural or man-made vibration environment; such as waves, tidal flaps, wind, earthquake or rain and so on. It is to test if the product is capable of sustaining the vibration environment exerted from transporting or usage along its effective life cycle; and certify the standard of design & functional requirement of product. The value of vibration testing is to confirm the reliability of products and effectively screen out the bad products in factory; avoiding damages occurred at arrival; and to assess the failure analysis on the non-performing products; expecting to reach a high standard, high-reliability products. The vibration test stresses on the continuity and fatigue; and contributes to the understanding of product’s status under vibration circumstance in a normal environment; and avoids the product’s unpredictable damage caused under certain vibrating frequency for a long time.
-
Saluki Technology Inc.
Saluki S2108 series Optical Network Tester is an intelligent high-precision optical network comprehensive tester with cloud wireless transmission, intelligent cloud platform and other functions. S2108 series adopts 7 inch capacitive touch screen, supports multi-point touch and integrates 18 functional modules internally. Compared to previous versions, it supports smart cloud platform, iONM, Multi-core measurement, 4G LTE SIM, GPS, Bluetooth and WIFI; built-in 8G storage capacity, can store more than 200,000 test data, and test data can be uploaded to the cloud wirelessly; PDF reports can be generated on the device and transmit them to the mobile terminal via WiFi & Bluetooth. S2108 series supports multi-tasks simultaneous operation, and VFL, OPM, LS functions can run in the background.
-
National Technical Systems
Compatibility and interoperability testing focuses on exercising the product-under-test under an array of software and hardware variables (e.g., different operating systems, additional software applications, such as web browsers, and hardware, such as graphics adapters, processors, chipsets, etc.). With almost three decades of growth and refinement, NTS’s test methodologies are unparalleled in the area of compatibility and interoperability testing. With our extensive in-house library of up-to-date software and hardware, NTS can simulate a wide variety of real-world environment in which your product may be utilized. Test failures are routinely regressed using industry standard methodologies, and known functional hardware and software. Compatibility testing seeks to verify the compatibility of a vendor’s product specifically with particular hardware or software (e.g., with the operating system, a word processor with a printer, etc.). Interoperability testing, on the other hand, typically focuses on validating “coexistence” (e.g., a word processor and spreadsheet program can both be installed on the same platform without causing problems with the other).
-
Model 7641 -
Jinan Testing Equipment IE Corporation
These COD gages use a high-temperature capacitive sensor and do not require any cooling. They will operate up to the maximum temperature limit of most environmental chambers used in materials testing. The Model 7641 is ideal for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. All units can be displaced slightly in compression for ease of installation. The COD gage is supplied with the advanced DT6229 controller. The standard output is 0-10VDC analog signal, factory calibrated with the COD gage. This system provides a number of functional enhancements, including: high speed digital output, built in calibration and tare functions, analog and digital filters, and more. The 7641 is readily interfaced with most existing test controllers, and may be directly connected to a data acquisition system or chart recorder, or directly to a PC. The 7641 may be used for strain controlled tests such as JIC.
-
TA-100 -
Tech-Aid Products
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
ARC Technology Solutions
In today’s fast paced manufacturing environment, where time to market and cost competitiveness is key, having a manufacturing partner like ARC can be a valuable resource for your company. ARC has a build-to-print manufacturing capability with our unique ‘engineer-to-print’ philosophy to make sure precision manufacturing and final build accuracy is top priority for your module level or system level builds. ARC can support up to several hundred module level assemblies (CCA subassemblies, cabling, mechanical and paneling elements) with abilities to perform a variety of software, embedded tasks and functional testing including a mixed signal test capability using our in-house MSAT (Mixed Signal Automated Tester) platform. We have a thorough process created through the development of our own products and test solutions. We know the importance of having a regimented manufacturing process, augmented with engineering expertise to address challenges that come up with building complex, high-mix, medium volume products.
-
MB BSR Suite -
MB Dynamics Inc.
MB BSR SUITE is the complete solution for all measurement tasks in the field of NVH, Squeak & Rattle and Sound Quality testing. Comprehensive analysis and assessment capabilities also enable the use of the BSR Suite for analysis and evaluation of functional and operating noise, vibrational effects on humans as well as the acoustic and haptic feedback of controls and actuators. Predefined test configurations for typical tasks such as multi-channel road load data acquisition, drive-file generation and objective Squeak & Rattle and Sound Quality testing allow for fast and simple operation. Signal statistics and user defined thresholds or reference-curves can be used for objective evaluation of different acoustic or haptic quality criteria. In addition the development and integration of application- or customer-specific analyses and evaluation methods is also possible at any time. Contact MB to find a solution for your measurement task!
